Dear WeatherCat station caregivers,
Late last week I noticed that my anemometer wasn't reporting any wind. I took a look and found . . . .
this!So . . .
grumble, grumble, grumble, . . . . I grabbed a pole long enough to give the wind speed cups a kick to free them from the spider web. When I did this there was an ominous development - WeatherCat didn't report any wind speed. I repeated this procedure with sadly the same results. I don't know if the anemometer had failed before I gave it a kick or if my pole was too harsh and broke the mechanism. Either way I had lost my wind speed sensor.
All this happened just before the Orinda Classic Car show so I had to let this matter slide until Sunday when I could start to respond to it. Since I have gotten some real help from Ryan Wilhour at Scaled Instruments back in 2014, I ordered a replacement Davis Vantage Pro-2 Anemometer from him:
https://www.scaledinstruments.com/shop/davis-instruments/davis-6410-anemometer-for-vantage-pro2-vantage-pro/ There are a number of really good discount vendors out there, so this isn't an exclusive endorsement. It is simply a result of my personal experiences. By the way Ryan is having a sale on some Davis components, so if you might have a need you might check his website out:
https://www.scaledinstruments.com/I paid the extra cost of having the anemometer shipped by the USPS next day air. It did arrive on time at a fraction of the cost of a private delivery company's price.
Unfortunately, my anemometer mast is secured to the house at a location that is full south and therefore extremely hot when in the sunlight. The days are getting shorter but the heat was such that I couldn't do this job much before 4pm when the mast was in the shade. I never intended to replace the anemometer so with some concern I tried to remove the wood screws securing the mast bracket on Monday afternoon. Fortunately, the bracket came free without any difficulties.
Yesterday the anemometer arrived and was packaged as can be seen in this photo:
While doing the work, I decided to simply unplug the anemometer cable and let WeatherCat continue running. It dutifully noted sensor errors but since I knew why there was no reason to be concerned. My
'WC Status Growler' AppleScript even reported the errors:
I was pleased to see this since this AppleScript has been fickle in the past to report sensor errors.
I removed the old anemometer and took this photo of the old and new side by side:
While there is no obvious signs of damage, it is clear that 9 years of being out-of-doors had taken it toll on the old anemometer. I carefully marked the location of the old anemometer so that the new one would be in the same position with respect to North and then I put on the new anemometer using the new hardware that Davis supplies. I then secured the cable along the mast with cable ties as can be seen here:
At this point I had to splice the signal cables into the old 50+ foot long cable that runs from the deck where the ISS transmitter is located to the anemometer mast. I had to purchase an 8 foot cable to get the splice kit since Davis no longer sells the splice kit separately. Since the day was already running short, I just spliced the cables and stopped there. I'll have to come back later to place the splice in the Davis supplied housing.
Before putting the mast back up I thought it was prudent to test everything and make sure the new anemometer was working properly.
. . . .
So I huffed, and puffed, and b-b-b-bblew at the anemometer cups!So much so that I caused a high wind warning!!!
NOT!! With the anemometer working properly, it was time to raise the mast. Luckily, I had purchased too many of the wood screws used to secure the mast bracket to the house, so I was able to replace all the screws. I use a somewhat unusual procedure to secure heavy objects to the house in that I use Gorilla Glue:
https://www.gorillatough.com/product/original-gorilla-glue/It is a polyurethane-based glue with some usual properties. The key property I exploit is that it is drawn toward moisture. Before putting the anemometer mast back up I first squirted some water into the screw-holes and let it sit for a few minutes. I then put in a squirt of Gorilla Glue just before putting the mast back up and securing it with the wood screws. Gorilla Glue will be drawn into any spots in the wood where the moisture has reached and then expands forming what is a effectively a "chemical anchor" to secure the screw. Since our house was built in 1947 out of very nice but soft redwood, the Gorilla Glue effectively spreads the stresses to a larger region of the wood insuring that the mast will remain secure.
This morning the skies were kind enough to make something of a display to greet the new anemometer:
So after 5 days, my weather station is once more able to dutifully report all the data expected of a Davis Vantage Pro-2!
Cheers, Edouard
P.S. I will add a posting explaining how to use the Davis cable splicing kits as soon as that task is finally accomplished.